电子技术论坛_中国专业的电子工程师学习交流社区-中电网技术论坛

标题: 编译问题 [打印本页]

作者: zhengz_2009 时间: 2010-2-3 15:12 标题: 编译问题

我刚开始使用飞思卡尔的单片机，第一次编译的时候，出现这样的话
executing C_layout.hwl
!OPEN source 0 0 60 39
NO CONNECTION
!Source < attributes MARKS off
!OPEN assembly 60 0 40 31
!Assembly < attributes ADR on,CODE off,ABSADR on,SYMB off,TOPPC 0xF88C
!OPEN procedure 0 39 60 17
!Procedure < attributes VALUES on,TYPES off
!OPEN register 60 31 40 25
!Register < attributes FORMAT AUTO,COMPLEMENT None
!OPEN memory 60 56 40 22
!Memory < attributes FORMAT hex,COMPLEMENT None,WORD 1,ASC on,ADR on,ADDRESS 0x80
!OPEN data 0 56 60 22
!Data:1 < attributes SCOPE global,COMPLEMENT None,FORMAT Symb,MODE automatic,UPDATERATE 10,NAMEWIDTH 16
!OPEN data 0 78 60 22
!Data:2 < attributes SCOPE local,COMPLEMENT None,FORMAT Symb,MODE automatic,UPDATERATE 10,NAMEWIDTH 16
!OPEN command 60 78 40 22
!Command < attributes CACHESIZE 1000
!bckcolor 50331647
!font 'Courier New' 9 BLACK
!AUTOSIZE on
!ACTIVATE Data:2 Command Procedure Data:1 Source Register Assembly Memory
done C_layout.hwl
Loading Target ...
Windows NT detected.
USB HCS08/HCS12 MULTILINK detected - Flash Version 5.28
Frequency change to ~3306457hz.
USB HCS08/HCS12 MULTILINK detected - Flash Version 5.28
Frequency change to ~4606192hz.
Device is 9S08LG32.
Mode is In-Circuit Debug.
IO registers loaded for MC9S08LG32 from G:\Program Files\Freescale\CodeWarrior for Microcontrollers V6.2\prog\REG\MCU1072.REG
executing .\cmd\BDM_P&E_Multilink_CyclonePro_startup.cmd
!// At startup the commands written below will be executed
Target Ready
done .\cmd\BDM_P&E_Multilink_CyclonePro_startup.cmd
Startup command file correctly executed.
executing .\cmd\BDM_P&E_Multilink_CyclonePro_preload.cmd
!// Before load the commands written below will be executed
done .\cmd\BDM_P&E_Multilink_CyclonePro_preload.cmd
Preload command file correctly executed.
USB HCS08/HCS12 MULTILINK detected - Flash Version 5.28
executing .\cmd\BDM_P&E_Multilink_CyclonePro_postload.cmd
!// After load the commands written below will be executed
MCU Device Selection has been changed.
!ORB 0x180F 0x80
done .\cmd\BDM_P&E_Multilink_CyclonePro_postload.cmd
Postload command file correctly executed.
main 0x8092 T
STARTED
RUNNING
Preset breakpoint encountered.
Breakpoint
in>

我不知道这样是不是有啥问题，因为我只是编了一段让led闪烁的很简单的程序，但是不成功，牛人们帮我看看，是哪有问题吗？谢谢哈

欢迎光临电子技术论坛_中国专业的电子工程师学习交流社区-中电网技术论坛 (http://bbs.eccn.com/)