电子技术论坛_中国专业的电子工程师学习交流社区-中电网技术论坛

标题: 往MC9S12DP256B内下载程序被提示：No programming voltage怎么回事？ [打印本页]

作者: malyyuer 时间: 2007-5-19 23:07 标题: 往MC9S12DP256B内下载程序被提示：No programming voltage怎么回事？

往MC9S12DP256B内下载程序被提示：No programming voltage怎么回事？
具体情况：
MCU clock speed: 2797000 Hz
Block Module Name Address Range Status
0 EEPROM 400 - FFF Blank - Unselected
1 FLASH_4000 4000 - 7FFF Programmed - Unselected
2 FLASH_C000 C000 - FFFF Programmed - Unselected
3 ALL_PPAGES 308000 -3FBFFF Programmed - Unselected
4 FLAT8000_P30 8000 - BFFF Programmed - Unselected

FP: The UNPROTECT command is not available for the EEPROM flash module => Skipped.

FP: The UNPROTECT command is not available for the FLASH_4000 flash module => Skipped.

FP: The UNPROTECT command is not available for the FLASH_C000 flash module => Skipped.

FP: The UNPROTECT command is not available for the ALL_PPAGES flash module => Skipped.

FP: The UNPROTECT command is not available for the FLAT8000_P30 flash module => Skipped.
executing .\cmd\P&E_Multilink_CyclonePro_vppon.cmd

!// Before programming the flash, the commands written below will be executed
done .\cmd\P&E_Multilink_CyclonePro_vppon.cmd

Vppon command file correctly executed.

FP: No programming voltage

FP: No programming voltage

FP: ALL_PPAGES flash module is bad or protected.
executing .\cmd\P&E_Multilink_CyclonePro_vppoff.cmd

!// After programming the flash, the commands written below will be executed
done .\cmd\P&E_Multilink_CyclonePro_vppoff.cmd

Vppoff command file correctly executed.
FP: Arm FLASH for loading.
executing .\cmd\P&E_Multilink_CyclonePro_vppon.cmd

!// Before programming the flash, the commands written below will be executed
done .\cmd\P&E_Multilink_CyclonePro_vppon.cmd

Vppon command file correctly executed.
executing .\cmd\P&E_Multilink_CyclonePro_vppoff.cmd

!// After programming the flash, the commands written below will be executed
done .\cmd\P&E_Multilink_CyclonePro_vppoff.cmd

Vppoff command file correctly executed.
FP: FLASH disarmed.
executing .\cmd\P&E_Multilink_CyclonePro_reset.cmd

!// After reset the commands written below will be executed
done .\cmd\P&E_Multilink_CyclonePro_reset.cmd

Reset command file correctly executed.
executing .\cmd\P&E_Multilink_CyclonePro_postload.cmd

!// After load the commands written below will be executed
RESET
done .\cmd\P&E_Multilink_CyclonePro_postload.cmd

Postload command file correctly executed.
main 0x308000 T
STARTED
RUNNING
ILLEGAL_BP

in>

其中在写程序前后分别执行了：
done .\cmd\P&E_Multilink_CyclonePro_vppon.cmd
和done .\cmd\P&E_Multilink_CyclonePro_vppoff.cmd
我看了这两个工程所生成得文件，是空的，跟这有关系么？
请各位不吝赐教！

作者: malyyuer 时间: 2007-5-19 23:09

晕啊！还是那个问题，我被愚了！
用Full Chip simulation模式不提示错误了，现在才发现：
Full Chip simulation模式是脱离硬件的仿真，其实他没有硬件也可以调试程序。最终还是没有能下进去啊！！
郁闷！哪位能指点一下。怎么回事啊？？？

欢迎光临电子技术论坛_中国专业的电子工程师学习交流社区-中电网技术论坛 (http://bbs.eccn.com/)