STM32使用fsmc控制NOR flash 例程（7） content, flash, memory

yuyang911220

/* Read back NOR memory and check content correctness */   
  for (Index = 0x00; (Index < BUFFER_SIZE) && (WriteReadStatus == 0); Index++)
  {
    if (RxBuffer[Index] != TxBuffer[Index])
    {
      WriteReadStatus = Index + 1;
    }
  }   if (WriteReadStatus == 0)
  { /* OK */
    /* Turn on LD1 */
    GPIO_SetBits(GPIOF, GPIO_Pin_6);
  }
  else
  { /* KO */
    /* Turn on LD2 */
    GPIO_SetBits(GPIOF, GPIO_Pin_7);     
  }
  while (1)
  {
  }
}
/*******************************************************************************
* Function Name  : RCC_Configuration
* Description    : Configures the different system clocks.
* Input          : None
* Output         : None
* Return         : None
*******************************************************************************/
void RCC_Configuration(void)
{   
  /* RCC system reset(for debug purpose) */
  RCC_DeInit();
  /* Enable HSE */
  RCC_HSEConfig(RCC_HSE_ON);
  /* Wait till HSE is ready */
  HSEStartUpStatus = RCC_WaitForHSEStartUp();
  if(HSEStartUpStatus == SUCCESS)
  {
    /* Enable Prefetch Buffer */
    FLASH_PrefetchBufferCmd(FLASH_PrefetchBuffer_Enable);
    /* Flash 2 wait state */
    FLASH_SetLatency(FLASH_Latency_2);
  
    /* HCLK = SYSCLK */
    RCC_HCLKConfig(RCC_SYSCLK_Div1);
  
    /* PCLK2 = HCLK */
    RCC_PCLK2Config(RCC_HCLK_Div1);
    /* PCLK1 = HCLK/2 */
    RCC_PCLK1Config(RCC_HCLK_Div2);
    /* PLLCLK = 8MHz * 9 = 72 MHz */
    RCC_PLLConfig(RCC_PLLSource_HSE_Div1, RCC_PLLMul_9);
    /* Enable PLL */
    RCC_PLLCmd(ENABLE);
    /* Wait till PLL is ready */
    while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET)
    {
    }
    /* Select PLL as system clock source */
    RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);
    /* Wait till PLL is used as system clock source */
    while(RCC_GetSYSCLKSource() != 0x08)
    {
    }
  }
}
/*******************************************************************************
* Function Name  : NVIC_Configuration
* Description    : Configures Vector Table base location.
* Input          : None
* Output         : None
* Return         : None
*******************************************************************************/
void NVIC_Configuration(void)
{
#ifdef  VECT_TAB_RAM  
  /* Set the Vector Table base location at 0x20000000 */
  NVIC_SetVectorTable(NVIC_VectTab_RAM, 0x0);
#else  /* VECT_TAB_FLASH  */
  /* Set the Vector Table base location at 0x08000000 */
  NVIC_SetVectorTable(NVIC_VectTab_FLASH, 0x0);   
#endif
}
/*******************************************************************************
* Function name : Fill_Buffer
* Description   : Fill the global buffer
* Input         : - pBuffer: pointer on the Buffer to fill
*                 - BufferSize: size of the buffer to fill
*                 - Offset: first value to fill on the Buffer
* Output param  : None
*******************************************************************************/
void Fill_Buffer(u16 *pBuffer, u16 BufferLenght, u32 Offset)
{
  u16 IndexTmp = 0;
  /* Put in global buffer same values */
  for (IndexTmp = 0; IndexTmp < BufferLenght; IndexTmp++ )
  {
    pBuffer[IndexTmp] = IndexTmp + Offset;
  }
}
#ifdef  DEBUG
/*******************************************************************************
* Function Name  : assert_failed
* Description    : Reports the name of the source file and the source line number
*                  where the assert_param error has occurred.
* Input          : - file: pointer to the source file name
*                  - line: assert_param error line source number
* Output         : None
* Return         : None
*******************************************************************************/
void assert_failed(u8* file, u32 line)
{
  /* User can add his own implementation to report the file name and line number,
     ex: printf("Wrong parameters value: file %s on line %d/r/n", file, line) */
  /* Infinite loop */
  while (1)
  {
  }
}
#endif
/******************* (C) COPYRIGHT 2008 STMicroelectronics *****END OF FILE****/